收藏本站
2.7 Installing I/O Cards
1. Orient the backplane with the CPU Card already installed and facing towards you as
shown in Figure 5.
R27 Q27 C27 R35
Q35 C35
Tip : It'seasiertoinstallthe
plastic brackets when you
install I/O cards starting
from the slot furthest away
from the CPU card. You
may have to remove the
CPU card to install the
brackets on the I/O card
in SLOT 0 .
Place tabs on
card into
alignment slot
Q20
C
C
B E
I/O Card
Q28
C
C
B E
CPU Card
RCM
SERIAL
JACK
RCM TxC RxC TxD
USER ACT LNK
RxD GND
CPU
ACT LNK
+ RS-485 ?
PWR
DS2
C52
C50
R44
R43
L1
R40
C44
R36
Q5
TP2
U12
CPU
Card
R24
Q2
U7
TP1
RN2
U4
RN1
U5
Q7
Q4
R35
SRAM
C20
RP3
U2
C5
C51
RP2
C6
Q6
R31
JP5
JP3
U5
RP1
R7
R4 +
TVS1
D6
C48
D4
TP3
C29
JP4
Flash
EPROM
U11
JP2
Flash
EPROM
C36
C37
USER +RAW GND
PWR
USER +RAW GND
POWER
IN
3
To
power supply
Note : The plastic brackets
on the CPU card are
attached on the opposite
side of the board relative
to the I/O cards.
Figure 5. Installing I/O Cards on the Backplane
2. Position the new I/O card above the backplane over any unused slot position ( SLOT 0 to
SLOT 6 ) as shown in Figure 5. Note the slot number and the type of I/O card since
Dynamic C addresses the I/O cards by slot number.
3. Carefully insert the I/O card header into the slot on the backplane and line up the tabs
on the I/O cards with the slots on the backplane as shown in Figure 5.
4. Use the two 4-40 screws supplied with the I/O card to anchor the plastic brackets on the CPU
Card or the I/O card firmly on the backplane. Tighten the screws as needed using a Phillips
screwdriver whose shaft is at least 3" (7 cm) long, but is no thicker than 0.16" (4 mm).
User ’s Manual
25
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
101-0545 PROTOTYPING BOARD FOR LP3500
101-0563 RCM3400 PROTO BOARD
101-0589 CLONING BOARD RABBIT
101-0688 CARD D/A EXPANSION RN1300
101-0954 KIT DEV RABBIT RCM3360/3370 INTL
101-1050-BE-00025 ADPT USB 2 A FEMALE-2 5PIN .25M
10112627-101LF MINI-SAS HD 1X2 EXT PCB
10112628-101LF MINI-SAS HD 1X4 EXT PCB
相关代理商/技术参数
101-0507 功能描述:模块化系统 - SOM RCM3000 RABBITCORE RoHS:否 制造商:Digi International 外观尺寸:ConnectCore 9P 处理器类型:ARM926EJ-S 频率:150 MHz 存储容量:8 MB, 16 MB 存储类型:NOR Flash, SDRAM 接口类型:I2C, SPI, UART 工作电源电压:3.3 V 最大工作温度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
101-0508 功能描述:模块化系统 - SOM RCM3010 RABBITCORE RoHS:否 制造商:Digi International 外观尺寸:ConnectCore 9P 处理器类型:ARM926EJ-S 频率:150 MHz 存储容量:8 MB, 16 MB 存储类型:NOR Flash, SDRAM 接口类型:I2C, SPI, UART 工作电源电压:3.3 V 最大工作温度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
101050-9 制造商:RUKO 功能描述:Bulk 制造商:RUKO 功能描述:STEP DRILL 4-12MMX1MM 制造商:RUKO 功能描述:STEP DRILL, 4-12MMX1MM 制造商:RUKO 功能描述:STEP DRILL, 4-12MMX1MM; Drill Bit Size Metric:4mm; Overall Length:65mm; SVHC:No SVHC (19-Dec-2012); Drill Bit Type:Step; Drill Point Diameter:4mm; Material:HSS; Range:4mm - 12mm; Shank Dia:6mm; Step:1mm ;RoHS Compliant: NA
101050BO 制造商:TE Connectivity 功能描述:
101051 制造商:RUKO 功能描述:STEP DRILL 4-20MMX2MM 制造商:RUKO 功能描述:STEP DRILL, 4-20MMX2MM 制造商:RUKO 功能描述:STEP DRILL, 4-20MMX2MM; Drill Bit Size Metric:4mm; Overall Length:75mm; SVHC:No SVHC (19-Dec-2012); Drill Bit Type:Step; Drill Point Diameter:4mm; Material:HSS; Range:4mm - 20mm; Shank Dia:8mm; Step:2mm ;RoHS Compliant: NA
10-105108-03G 制造商:Amphenol Aerospace 功能描述:10-105108-03G
10-105108-03P 制造商:Amphenol Aerospace 功能描述:10-105108-03P
10-105108-04P 制造商:Amphenol Aerospace 功能描述:10-105108-04P